Newton's Laws of Motion

Newton's First Law and Inertia

By the end of the lesson, the learner should be able to:
State Newton's first law of motion
-Define inertia and relate it to mass
-Explain the concept of balanced and unbalanced forces
-Give examples of Newton's first law in daily life
-Understand the need for seat belts and safety devices

In groups, learners are guided to:
Q/A review on forces from previous studies
-Demonstration: cardboard and coin experiment
-Demonstration: hitting bottom coin from stack
-Discussion on inertia and its relationship to mass
-Explanation of seat belts and safety devices in vehicles
-Analysis of forces acting on aircraft in flight

Cardboard
-Glass tumbler
-Coins
-Charts showing aircraft forces
-Pictures of safety devices
-Demonstration materials
-Balance

KLB Secondary Physics Form 3, Pages 65-67

Newton's Laws of Motion

Momentum and its Applications

By the end of the lesson, the learner should be able to:
Define momentum and state its SI unit
-Calculate momentum using p = mv
-Identify momentum as a vector quantity
-Solve problems involving momentum calculations
-Compare momentum of different objects

In groups, learners are guided to:
Review Newton's first law through Q/A
-Introduction to momentum concept with examples
-Demonstration: comparing stopping distances of vehicles
-Worked examples on momentum calculations
-Problem-solving session with various scenarios
-Discussion on factors affecting momentum

Calculator
-Toy cars of different masses
-Stopwatch
-Measuring tape
-Worked examples charts
-Problem worksheets

KLB Secondary Physics Form 3, Pages 67-68

Newton's Laws of Motion

Newton's Second Law of Motion
Experimental Verification of Newton's Second Law
Impulse and Change in Momentum

By the end of the lesson, the learner should be able to:
State Newton's second law of motion
-Derive the relationship F = ma
-Define the Newton as unit of force
-Understand rate of change of momentum
-Apply F = ma to solve problems
Investigate relationship between force and acceleration
-Investigate relationship between mass and acceleration
-Verify F = ma experimentally
-Analyze ticker-tape results
-Draw conclusions from experimental data

In groups, learners are guided to:
Q/A on momentum concepts
-Derivation of F = ma from Newton's second law
-Definition of the Newton using F = ma
-Demonstration using ticker-timer and trolley
-Worked examples applying F = ma
-Problem-solving session with force calculations
Review F = ma through Q/A
-Experiment: Force vs acceleration (constant mass)
-Experiment: Mass vs acceleration (constant force)
-Analysis of ticker-tape patterns
-Data collection and graph plotting
-Discussion on experimental errors and improvements

Ticker-timer
-Trolley
-Runway
-Elastic cords
-Masses
-Calculator
-Force diagrams
-Worked examples
Ticker-timer
-Trolley
-Ticker tape
-Elastic cords
-Various masses
-Scissors
-Graph paper
-Rulers
-Calculator
Graph paper
-Force-time graph examples
-Charts showing car safety features
-Sports equipment examples
-Worked examples

KLB Secondary Physics Form 3, Pages 68-74
KLB Secondary Physics Form 3, Pages 69-71

Newton's Laws of Motion

Newton's Third Law of Motion

By the end of the lesson, the learner should be able to:
State Newton's third law of motion
-Understand action and reaction pairs
-Explain that forces occur in pairs
-Apply third law to various situations
-Analyze motion in different scenarios

In groups, learners are guided to:
Review impulse concepts through Q/A
-Demonstration: walking and floor interaction
-Demonstration: jumping from boat scenario
-Discussion on action-reaction pairs
-Examples from daily life: walking, swimming, rocket propulsion
-Problem-solving involving third law

Books for pressure demonstration
-Spring balances
-Trolleys
-String
-Charts showing action-reaction examples
-Pictures of rockets and jets

KLB Secondary Physics Form 3, Pages 75-80

Newton's Laws of Motion

Applications of Newton's Laws - Lifts and Apparent Weight

By the end of the lesson, the learner should be able to:
Analyze forces in accelerating lifts
-Calculate apparent weight in different situations
-Understand weightlessness concept
-Apply Newton's laws to lift problems
-Solve problems involving vertical motion

In groups, learners are guided to:
Q/A on Newton's third law
-Analysis of forces in lift moving upward with acceleration
-Analysis of forces in lift moving downward with acceleration
-Calculation of apparent weight in different scenarios
-Discussion on weightlessness in spacecraft
-Problem-solving session on lift problems

Spring balance
-Mass
-Lift diagrams
-Calculator
-Free-body diagram charts
-Worked examples
-Problem worksheets

KLB Secondary Physics Form 3, Pages 76-78

Newton's Laws of Motion

Conservation of Linear Momentum

By the end of the lesson, the learner should be able to:
State the law of conservation of momentum
-Apply conservation of momentum to collisions
-Distinguish between elastic and inelastic collisions
-Solve collision problems
-Understand momentum in explosions

In groups, learners are guided to:
Review lift problems through Q/A
-Statement and explanation of conservation of momentum
-Demonstration: colliding trolleys or balls
-Analysis of elastic and inelastic collisions
-Worked examples on collision problems
-Discussion on explosions and momentum conservation

Trolleys
-Plasticine
-Marbles
-Spring balance
-Measuring tape
-Stopwatch
-Calculator
-Collision demonstration apparatus

KLB Secondary Physics Form 3, Pages 80-86

Newton's Laws of Motion

Applications of Momentum Conservation - Rockets and Jets
Friction - Types and Laws

By the end of the lesson, the learner should be able to:
Explain rocket and jet propulsion
-Apply momentum conservation to propulsion systems
-Understand recoil velocity calculations
-Analyze garden sprinkler operation
-Solve recoil problems
Define friction and explain its molecular basis
-Distinguish between static and kinetic friction
-State and apply laws of friction
-Understand advantages and disadvantages of friction
-Identify methods of reducing friction

In groups, learners are guided to:
Q/A review on momentum conservation
-Explanation of rocket propulsion principle
-Analysis of jet engine operation
-Calculation of recoil velocities
-Demonstration: balloon rocket or garden sprinkler
-Problem-solving on recoil scenarios
Review momentum applications through Q/A
-Demonstration: block on table with increasing force
-Explanation of molecular basis of friction
-Discussion on types of friction: static, kinetic, rolling
-Investigation of factors affecting friction
-Examples of friction in daily life and technology

Balloons
-String
-Straws
-Garden sprinkler (if available)
-Charts showing rocket/jet engines
-Calculator
-Worked examples
Wooden blocks
-Different surfaces
-Spring balance
-Weights
-Lubricants
-Sandpaper
-Charts showing friction applications
-Ball bearings

KLB Secondary Physics Form 3, Pages 86-87
KLB Secondary Physics Form 3, Pages 87-90

Newton's Laws of Motion

Viscosity and Terminal Velocity

By the end of the lesson, the learner should be able to:
Define viscosity and explain its effects
-Understand motion of objects through fluids
-Explain terminal velocity concept
-Analyze forces on falling objects in fluids
-Investigate factors affecting terminal velocity

In groups, learners are guided to:
Q/A on friction concepts
-Demonstration: steel ball falling through different liquids
-Explanation of viscous drag and terminal velocity
-Analysis of forces: weight, upthrust, and viscous drag
-Investigation of terminal velocity using glycerine
-Discussion on applications: parachutes, rain drops

Tall measuring cylinder
-Glycerine
-Steel ball bearings
-Water
-Stopwatch
-Rubber bands
-Ruler
-Different viscous liquids

KLB Secondary Physics Form 3, Pages 90-93

Work, Energy, Power and Machines

Sources of Energy
Forms of Energy

By the end of the lesson, the learner should be able to:
Identify different sources of energy
-Distinguish between renewable and non-renewable energy sources
-Classify energy sources into appropriate categories
-Discuss advantages and disadvantages of different energy sources
-Understand energy crisis and conservation needs

In groups, learners are guided to:
Q/A on energy experiences in daily life
-Discussion on various energy sources students know
-Classification activity: renewable vs non-renewable
-Group work on energy source advantages/disadvantages
-Presentation on local energy sources in Kenya
-Discussion on energy conservation importance

Charts showing energy sources
-Pictures of solar panels, wind mills
-Samples: coal, wood, batteries
-Energy source classification cards
-Local energy examples
-Conservation posters
Battery and bulb
-Moving trolley
-Rubbing blocks for friction
-Electrical appliances
-Tuning fork
-Torch
-Energy forms charts
-Real objects showing energy forms

KLB Secondary Physics Form 3, Pages 93-95

Work, Energy, Power and Machines

Energy Transformation and Conservation

By the end of the lesson, the learner should be able to:
Understand energy transformations between different forms
-State the law of conservation of energy
-Identify transducers and their functions
-Apply conservation of energy to various situations
-Draw energy transformation diagrams

In groups, learners are guided to:
Q/A on forms of energy
-Demonstration: energy transformations in hydroelectric power
-Examples of transducers: battery, dynamo, solar cell
-Statement and explanation of energy conservation law
-Drawing energy flow diagrams
-Discussion on energy losses and efficiency

Dynamo
-Battery
-Solar cell (if available)
-Charts showing energy transformations
-Transducer examples
-Energy flow diagrams
-Hydroelectric model setup

KLB Secondary Physics Form 3, Pages 96-97

Work, Energy, Power and Machines

Work and its Calculation
Work with Variable Forces

By the end of the lesson, the learner should be able to:
Define work in scientific terms
-State the condition for work to be done
-Calculate work using W = F × d
-Understand work as a scalar quantity
-Solve problems involving work calculations
Calculate work done by variable forces
-Interpret force-distance graphs
-Find work done using area under graphs
-Understand positive and negative work
-Apply graphical methods to work calculations

In groups, learners are guided to:
Review energy transformations through Q/A
-Definition of work with emphasis on force and displacement
-Demonstration: lifting objects, pushing trolleys
-Worked examples on work calculations
-Discussion on when no work is done
-Problem-solving session on work calculations
Q/A review on work calculations
-Introduction to variable forces
-Plotting force-distance graphs
-Demonstration: stretching spring with varying force
-Calculation of areas under graphs
-Worked examples with triangular and trapezoidal areas

Spring balance
-Masses
-Trolley
-Measuring tape
-Calculator
-Force and displacement demonstrations
-Worked examples charts
-Problem worksheets
Graph paper
-Springs
-Force meter
-Ruler
-Calculator
-Force-distance graph examples
-Different shaped area examples
-Demonstration springs

KLB Secondary Physics Form 3, Pages 96-99
KLB Secondary Physics Form 3, Pages 99-100

Work, Energy, Power and Machines

Gravitational Potential Energy

By the end of the lesson, the learner should be able to:
Define gravitational potential energy
-Derive P.E. = mgh
-Calculate potential energy at different heights
-Understand reference levels for potential energy
-Solve problems involving potential energy

In groups, learners are guided to:
Review variable force work through Q/A
-Demonstration: lifting objects to different heights
-Derivation of P.E. = mgh
-Discussion on choice of reference level
-Worked examples on potential energy calculations
-Problem-solving session with gravitational P.E.

Masses of different sizes
-Measuring tape
-Spring balance
-Calculator
-Height measurement setup
-Worked examples
-Gravitational P.E. charts

KLB Secondary Physics Form 3, Pages 100-102

Work, Energy, Power and Machines

Kinetic Energy

By the end of the lesson, the learner should be able to:
Define kinetic energy
-Derive K.E. = ½mv²
-Calculate kinetic energy of moving objects
-Understand relationship between work and kinetic energy
-Apply work-energy theorem

In groups, learners are guided to:
Q/A on potential energy concepts
-Demonstration: moving trolleys at different speeds
-Derivation of K.E. = ½mv² using work-energy theorem
-Worked examples on kinetic energy calculations
-Discussion on work-energy theorem
-Problem-solving session on kinetic energy

Trolleys
-Stopwatch
-Measuring tape
-Spring balance
-Calculator
-Kinetic energy demonstration setup
-Speed measurement apparatus

KLB Secondary Physics Form 3, Pages 102-105

Work, Energy, Power and Machines

Conservation of Mechanical Energy

By the end of the lesson, the learner should be able to:
Apply conservation of energy to mechanical systems
-Analyze energy changes in pendulums and projectiles
-Solve problems using conservation of energy
-Understand energy transformations in oscillating systems
-Calculate energy at different positions

In groups, learners are guided to:
Review kinetic energy through Q/A
-Demonstration: simple pendulum energy changes
-Analysis of energy at different positions in pendulum swing
-Discussion on energy conservation in projectile motion
-Worked examples using conservation of energy
-Problem-solving on energy conservation

Simple pendulum setup
-Measuring tape
-Stopwatch
-Masses
-Calculator
-Pendulum energy charts
-Conservation examples
-String and bob

KLB Secondary Physics Form 3, Pages 104-106

Work, Energy, Power and Machines

Power and its Applications
Simple Machines - Introduction and Terminology
Levers - Types and Applications

By the end of the lesson, the learner should be able to:
Define power as rate of doing work
-Calculate power using P = W/t and P = Fv
-State SI unit of power (Watt)
-Understand power ratings of appliances
-Solve problems involving power calculations
Classify levers into three types
-Identify examples of each type of lever
-Apply principle of moments to levers
-Calculate forces in lever systems
-Understand applications of different lever types

In groups, learners are guided to:
Q/A on energy conservation
-Definition of power with examples
-Derivation of P = W/t and P = Fv
-Discussion on power ratings of electrical appliances
-Worked examples on power calculations
-Investigation: measuring power of students climbing stairs
Q/A on machine terminology
-Classification of levers: Class I, II, and III
-Demonstration: examples of each lever type
-Application of principle of moments
-Worked examples on lever calculations
-Identification of levers in daily life tools

Stopwatch
-Measuring tape
-Spring balance
-Calculator
-Electrical appliances for power ratings
-Stairs for practical work
-Power calculation charts
Simple lever setup
-Masses for loads
-Ruler
-Machine terminology charts
-Efficiency calculation examples
Various lever examples
-Rulers
-Masses
-Spring balance
-Fulcrum supports
-Lever classification charts
-Daily life lever examples
-Calculator

KLB Secondary Physics Form 3, Pages 106-108
KLB Secondary Physics Form 3, Pages 112-114

Work, Energy, Power and Machines

Pulleys - Fixed and Movable

By the end of the lesson, the learner should be able to:
Understand operation of fixed and movable pulleys
-Calculate M.A. and V.R. for different pulley systems
-Analyze block and tackle arrangements
-Solve problems involving pulley systems
-Understand advantages of pulley systems

In groups, learners are guided to:
Review lever types through Q/A
-Demonstration: fixed pulley operation
-Demonstration: single movable pulley
-Analysis of block and tackle systems
-Calculation of M.A. and V.R. for different arrangements
-Problem-solving on pulley systems

Pulley blocks
-String
-Masses
-Spring balance
-Pulley arrangements
-Block and tackle setup
-Calculator
-Pulley system diagrams

KLB Secondary Physics Form 3, Pages 115-120

Work, Energy, Power and Machines

Inclined Planes and Screws

By the end of the lesson, the learner should be able to:
Understand inclined plane as a machine
-Calculate M.A. and V.R. for inclined planes
-Analyze screw as an inclined plane
-Understand applications of inclined planes
-Solve problems involving inclined planes

In groups, learners are guided to:
Q/A on pulley systems
-Demonstration: moving load up inclined plane
-Measurement of effort and load for inclined plane
-Calculation of M.A. and V.R. for inclined plane
-Discussion on screw as modified inclined plane
-Examples of inclined planes in daily life

Inclined plane setup
-Trolley or wooden block
-Spring balance
-Measuring tape
-Protractor
-Calculator
-Screw examples
-Various inclined plane models

KLB Secondary Physics Form 3, Pages 114-115

Work, Energy, Power and Machines

Gears and Hydraulic Systems

By the end of the lesson, the learner should be able to:
Understand gear systems and their operation
-Calculate V.R. for gear systems
-Explain hydraulic lift principle
-Apply Pascal's principle to hydraulic systems
-Calculate M.A. and V.R. for hydraulic systems

In groups, learners are guided to:
Review inclined planes through Q/A
-Demonstration: gear system operation
-Calculation of gear ratios and V.R.
-Explanation of hydraulic lift principle
-Demonstration: Pascal's principle using syringes
-Calculation of hydraulic system parameters

Gear wheels
-Bicycle for gear demonstration
-Syringes of different sizes
-Water
-Tubes
-Calculator
-Hydraulic system diagrams
-Gear ratio charts

KLB Secondary Physics Form 3, Pages 116-119

Work, Energy, Power and Machines
Current Electricity (II)

Efficiency of Machines
Electric Current and Measurement

By the end of the lesson, the learner should be able to:
Understand factors affecting machine efficiency
-Calculate efficiency using different methods
-Investigate efficiency of various machines
-Understand energy losses in machines
-Discuss methods to improve efficiency
Define electric current and state its SI unit
-Understand conventional current flow
-Use ammeters correctly to measure current
-Read ammeter scales accurately
-Understand current as rate of flow of charge

In groups, learners are guided to:
Q/A on gears and hydraulic systems
-Investigation: efficiency of pulley system
-Discussion on factors causing energy losses
-Measurement of input and output work
-Calculation of efficiency for different machines
-Discussion on improving machine efficiency
Q/A review on basic electricity from Form 2
-Definition of electric current and conventional flow
-Demonstration: proper ammeter connection in series
-Practice reading different ammeter scales
-Discussion on digital vs analogue meters
-Safety precautions when using electrical equipment

Various machines for testing
-Spring balances
-Measuring tape
-Stopwatch
-Calculator
-Efficiency measurement setup
-Lubricants for demonstration
Ammeters (analogue and digital)
-Dry cells
-Connecting wires
-Bulbs
-Switches
-Ammeter scale charts
-Safety equipment

KLB Secondary Physics Form 3, Pages 120-123
KLB Secondary Physics Form 3, Pages 126-130

Current Electricity (II)

Series and Parallel Circuits - Current Distribution

By the end of the lesson, the learner should be able to:
Investigate current in series circuits
-Investigate current in parallel circuits
-Apply Kirchhoff's current law
-Understand current division in parallel circuits
-Solve problems involving current distribution

In groups, learners are guided to:
Review ammeter usage through Q/A
-Experiment: measuring current in series circuit
-Experiment: measuring current in parallel circuit
-Analysis of current readings and patterns
-Statement of Kirchhoff's current law
-Problem-solving on current distribution

Multiple ammeters
-Bulbs
-Connecting wires
-Dry cells
-Switches
-Circuit boards
-Calculator
-Current distribution worksheets

KLB Secondary Physics Form 3, Pages 130-133

Current Electricity (II)

Potential Difference and Voltage Measurement
Series and Parallel Circuits - Voltage Distribution

By the end of the lesson, the learner should be able to:
Define potential difference in terms of work done
-State the SI unit of potential difference
-Use voltmeters correctly to measure voltage
-Understand voltage measurement across components
-Read voltmeter scales accurately

In groups, learners are guided to:
Q/A on current distribution
-Definition of potential difference and work done per unit charge
-Demonstration: proper voltmeter connection in parallel
-Practice measuring voltage across different components
-Comparison of voltmeter and ammeter connections
-Safety considerations in voltage measurement

Voltmeters (analogue and digital)
-Dry cells
-Resistors
-Bulbs
-Connecting wires
-Switches
-Voltmeter scale charts
-Work and charge demonstration materials
Multiple voltmeters
-Various resistors
-Circuit boards
-Calculator
-Voltage distribution worksheets

KLB Secondary Physics Form 3, Pages 126-129

Current Electricity (II)

Ohm's Law - Investigation and Verification

By the end of the lesson, the learner should be able to:
State Ohm's law
-Investigate relationship between voltage and current
-Plot V-I graphs for ohmic conductors
-Verify Ohm's law experimentally
-Understand conditions for Ohm's law validity

In groups, learners are guided to:
Q/A on voltage distribution
-Experiment: varying voltage and measuring current through resistor
-Data collection and table completion
-Plotting V-I graph and analyzing slope
-Statement and verification of Ohm's law
-Discussion on temperature and other conditions

Rheostat
-Ammeter
-Voltmeter
-Resistor coils
-Connecting wires
-Dry cells
-Graph paper
-Calculator
-Ruler

KLB Secondary Physics Form 3, Pages 131-135

Current Electricity (II)

Electrical Resistance and Ohm's Law Applications
Ohmic and Non-Ohmic Conductors

By the end of the lesson, the learner should be able to:
Define electrical resistance and its SI unit
-Apply Ohm's law to calculate V, I, and R
-Understand the relationship R = V/I
-Solve problems using Ohm's law
-Convert between different units of resistance
Distinguish between ohmic and non-ohmic conductors
-Investigate V-I characteristics of different materials
-Understand why some materials don't obey Ohm's law
-Analyze V-I graphs for various conductors
-Identify practical applications of non-ohmic conductors

In groups, learners are guided to:
Review Ohm's law investigation through Q/A
-Definition of electrical resistance as V/I ratio
-Worked examples applying Ohm's law triangle
-Unit conversions: Ω, kΩ, MΩ
-Problem-solving session on Ohm's law calculations
-Discussion on factors affecting resistance
Q/A on Ohm's law applications
-Experiment: V-I characteristics of filament bulb
-Experiment: V-I characteristics of diode
-Comparison of different V-I graph shapes
-Discussion on temperature effects on resistance
-Applications of non-ohmic conductors

Calculator
-Ohm's law triangle charts
-Resistor color code charts
-Various resistors
-Multimeter
-Problem worksheets
-Unit conversion charts
Filament bulbs
-Diodes
-Thermistors
-LDR
-Ammeter
-Voltmeter
-Rheostat
-Graph paper
-Various conductors for testing

KLB Secondary Physics Form 3, Pages 131-135
KLB Secondary Physics Form 3, Pages 134-135

Current Electricity (II)

Types of Resistors and Their Applications

By the end of the lesson, the learner should be able to:
Identify different types of resistors
-Understand fixed and variable resistors
-Read resistor color codes
-Understand applications of special resistors
-Use rheostats and potentiometers

In groups, learners are guided to:
Review ohmic vs non-ohmic conductors through Q/A
-Identification of resistor types: carbon, wire-wound, variable
-Practice reading resistor color codes
-Demonstration: rheostat and potentiometer operation
-Discussion on thermistors and LDR applications
-Practical applications in circuits

Various resistor types
-Color code charts
-Rheostat
-Potentiometer
-Thermistor
-LDR
-Multimeter
-Circuit boards
-Application examples

KLB Secondary Physics Form 3, Pages 135-140

Current Electricity (II)

Measurement of Resistance - Voltmeter-Ammeter Method

By the end of the lesson, the learner should be able to:
Describe voltmeter-ammeter method
-Set up circuits for resistance measurement
-Calculate resistance from V and I readings
-Understand limitations of the method
-Analyze experimental errors

In groups, learners are guided to:
Q/A on resistor types
-Setup of voltmeter-ammeter circuit
-Measurement of voltage and current for unknown resistor
-Calculation of resistance using R = V/I
-Discussion on measurement errors and accuracy
-Comparison with multimeter readings

Unknown resistors
-Voltmeter
-Ammeter
-Rheostat
-Connecting wires
-Dry cells
-Switches
-Calculator
-Multimeter for comparison

KLB Secondary Physics Form 3, Pages 140-142

Current Electricity (II)

Wheatstone Bridge Method

By the end of the lesson, the learner should be able to:
Understand the principle of Wheatstone bridge
-Set up Wheatstone bridge circuit
-Balance the bridge for resistance measurement
-Calculate unknown resistance using bridge equation
-Appreciate accuracy of Wheatstone bridge method

In groups, learners are guided to:
Review voltmeter-ammeter method through Q/A
-Introduction to Wheatstone bridge principle
-Demonstration of bridge balance condition
-Setup and operation of Wheatstone bridge
-Calculation using R₁/R₂ = R₃/R₄
-Comparison of accuracy with other methods

Wheatstone bridge apparatus
-Galvanometer
-Known resistors
-Unknown resistors
-Connecting wires
-Battery
-Calculator
-Bridge equation charts

KLB Secondary Physics Form 3, Pages 142-144

Current Electricity (II)

Resistors in Series - Theory and Calculations
Resistors in Parallel - Theory and Calculations
Mixed Circuits - Series-Parallel Combinations

By the end of the lesson, the learner should be able to:
Derive formula for resistors in series
-Calculate total resistance for series combination
-Understand current and voltage in series circuits
-Solve problems involving series resistors
-Apply series resistance in circuit analysis
Analyze circuits with series-parallel combinations
-Apply reduction techniques to complex circuits
-Calculate total resistance of mixed circuits
-Determine current and voltage in different branches
-Solve complex circuit problems

In groups, learners are guided to:
Q/A on resistance measurement methods
-Derivation of Rs = R₁ + R₂ + R₃...
-Demonstration: measuring total resistance of series combination
-Analysis of current (same) and voltage (divided) in series
-Worked examples on series resistance calculations
-Problem-solving session
Q/A on parallel resistance
-Introduction to mixed circuit analysis techniques
-Step-by-step reduction of complex circuits
-Worked examples on series-parallel combinations
-Problem-solving on mixed circuits
-Discussion on circuit analysis strategies

Resistors of known values
-Multimeter
-Connecting wires
-Circuit boards
-Calculator
-Series circuit diagrams
-Problem worksheets
-Parallel circuit diagrams
Various resistors
-Circuit boards
-Connecting wires
-Multimeter
-Calculator
-Complex circuit diagrams
-Step-by-step analysis charts

KLB Secondary Physics Form 3, Pages 144-147
KLB Secondary Physics Form 3, Pages 150-153

Current Electricity (II)

Electromotive Force (EMF) and Terminal Voltage

By the end of the lesson, the learner should be able to:
Define electromotive force (EMF)
-Distinguish between EMF and terminal voltage
-Understand the concept of lost voltage
-Relate EMF to work done by the cell
-Measure EMF using high resistance voltmeter

In groups, learners are guided to:
Review mixed circuits through Q/A
-Definition of EMF as work done per unit charge
-Demonstration: measuring EMF with open circuit
-Comparison of EMF and terminal voltage under load
-Discussion on energy conversion in cells
-Measurement techniques for EMF

High resistance voltmeter
-Various cells
-Switches
-Resistors
-Connecting wires
-EMF measurement setup
-Energy conversion charts

KLB Secondary Physics Form 3, Pages 150-152

Current Electricity (II)

Internal Resistance of Cells

By the end of the lesson, the learner should be able to:
Define internal resistance
-Understand the relationship E = V + Ir
-Calculate internal resistance experimentally
-Understand factors affecting internal resistance
-Apply internal resistance in circuit calculations

In groups, learners are guided to:
Q/A on EMF concepts
-Introduction to internal resistance concept
-Derivation of E = V + Ir relationship
-Experiment: measuring internal resistance using different loads
-Plotting E vs R graph to find internal resistance
-Discussion on factors affecting internal resistance

Various cells
-Resistors of different values
-Voltmeter
-Ammeter
-Connecting wires
-Graph paper
-Calculator
-Internal resistance apparatus

KLB Secondary Physics Form 3, Pages 150-153

Current Electricity (II)

Cells in Series and Parallel

By the end of the lesson, the learner should be able to:
Analyze cells connected in series
-Analyze cells connected in parallel
-Calculate total EMF and internal resistance
-Understand advantages of different connections
-Solve problems involving cell combinations

In groups, learners are guided to:
Review internal resistance through Q/A
-Analysis of identical cells in series connection
-Analysis of identical cells in parallel connection
-Calculation of equivalent EMF and internal resistance
-Discussion on practical applications and advantages
-Problem-solving on cell combinations

Multiple identical cells
-Connecting wires
-Voltmeter
-Ammeter
-Resistors
-Calculator
-Cell combination diagrams
-Problem worksheets

KLB Secondary Physics Form 3, Pages 152-153

Current Electricity (II)
Electrostatics II

Advanced Circuit Analysis and Problem Solving
Electric field patterns and charge distribution
Lightning arrestor and capacitance introduction
Factors affecting capacitance and types of capacitors

By the end of the lesson, the learner should be able to:
Apply Kirchhoff's laws to complex circuits
-Solve circuits with multiple sources
-Analyze circuits with internal resistance
-Use systematic approaches to circuit problems
-Integrate all electricity concepts
Explain working principle of lightning arrestor
- Describe charge concentration at sharp points
- Define capacitance and state SI units
- Describe parallel-plate capacitor structure

In groups, learners are guided to:
Q/A on cell combinations
-Application of Kirchhoff's current and voltage laws
-Systematic approach to complex circuit analysis
-Worked examples with multiple EMF sources
-Problem-solving session covering all electricity topics
-Discussion on practical circuit applications
Demonstration of charge concentration at points using wind-mill experiment
- Discussion on lightning protection applications
- Introduction to capacitance concept
- Demonstration of capacitor charging process

Complex circuit examples
-Calculator
-Circuit analysis worksheets
-Multiple EMF sources
-Various resistors
-Comprehensive problem sets
-Kirchhoff's law charts
High voltage source, Wire electrodes, Petri-dish, Castor oil, Chalk dust, Spherical and pear-shaped conductors, Proof-plane, Gold-leaf electroscope
Wind-mill model, Point charges, Lightning arrestor photos, Parallel-plate capacitors, Battery, Voltmeter, Milliammeter
Aluminium plates, Various dielectric materials, Electroscope, Paper capacitors, Electrolytic capacitors, Variable air capacitors, Measuring instruments

KLB Secondary Physics Form 3, Pages 126-153
KLB Secondary Physics Form 3, Pages 181-185

Electrostatics II

Capacitors in series and parallel
Energy stored in capacitors
Complex capacitor problems

By the end of the lesson, the learner should be able to:
Derive effective capacitance for series combination
- Derive effective capacitance for parallel combination
- Explain charge and voltage relationships
- Calculate individual charges and voltages

In groups, learners are guided to:
Mathematical derivation of series formula (1/C = 1/C₁ + 1/C₂)
- Mathematical derivation of parallel formula (C = C₁ + C₂)
- Problem solving with capacitor combinations
- Practical verification using circuits

Capacitors of different values, Voltmeters, Ammeters, Battery, Connecting wires, Calculators, Circuit boards
Charged capacitors, Energy calculation worksheets, Graphing materials, Calculators, Safety equipment
Complex circuit diagrams, Advanced problem worksheets, Graphing materials, Calculators, Past examination papers

KLB Secondary Physics Form 3, Pages 188-191

Electrostatics II
Heating Effect of Electric Current

Applications of capacitors
Electrical safety - fuses and circuit protection

By the end of the lesson, the learner should be able to:
Explain use in rectification and smoothing circuits
- Describe applications in tuning circuits
- State use in delay circuits and camera flash
- Solve comprehensive numerical problems on all topics

In groups, learners are guided to:
Discussion on practical applications in electronics
- Demonstration of smoothing circuits
- Explanation of tuning and delay functions
- Comprehensive revision and problem solving covering all electrostatics topics

Circuit diagrams, Smoothing circuit demo, Radio tuning circuits, Camera flash unit, Revision charts, Past examination papers
Various fuses, Fuse holders, Circuit diagrams, Safety equipment demonstrations, Rating calculations

KLB Secondary Physics Form 3, Pages 192-193

Heating Effect of Electric Current

Efficiency calculations and motor problems
Series and parallel heating circuits

By the end of the lesson, the learner should be able to:
Calculate efficiency of electrical devices
- Solve problems involving motors and mechanical work
- Analyze power input vs power output
- Calculate overall efficiency in systems

In groups, learners are guided to:
Problem solving on device efficiency
- Motor efficiency calculations
- Analysis of energy conversions
- Real-world efficiency problems

Motor specifications, Efficiency calculation worksheets, Power meters, Mechanical loading systems
Resistors in circuits, Ammeters, Voltmeters, Power calculation sheets, Circuit boards

KLB Secondary Physics Form 3, Pages 201-204

Quantity of Heat

Heat capacity and specific heat capacity
Determination of specific heat capacity - method of mixtures for solids
Determination of specific heat capacity - electrical method
Specific heat capacity of liquids and continuous flow method
Change of state and latent heat concepts

By the end of the lesson, the learner should be able to:
Define heat capacity and specific heat capacity
- State SI units for both quantities
- Distinguish between heat capacity and specific heat capacity
- Use formula Q = mcθ in simple calculations
Describe electrical method for solids
- Perform electrical heating experiment
- Calculate electrical energy supplied
- Determine specific heat capacity using electrical method

In groups, learners are guided to:
Q/A on heat concepts from previous studies
- Discussion on definitions and units
- Comparison of heat capacity vs specific heat capacity
- Simple problem solving using Q = mcθ formula
Experiment using electrical heating of metal block
- Measurement of voltage, current and time
- Calculation of electrical energy supplied
- Determination of specific heat capacity

Charts on heat definitions, Calculators, Simple problem worksheets, Various materials for comparison
Metal blocks, Beakers, Water, Thermometers, Weighing balance, Heat source, Well-lagged calorimeter, Stirrer
Metal cylinder with heater, Voltmeter, Ammeter, Thermometer, Stopwatch, Insulating materials, Power supply
Calorimeter, Electrical heater, Water, Measuring instruments, Continuous flow apparatus diagram, Problem sets
Naphthalene, Test tubes, Thermometer, Stopwatch, Graph paper, Heat source, Cooling apparatus

KLB Secondary Physics Form 3, Pages 206-209
KLB Secondary Physics Form 3, Pages 212-214

Quantity of Heat

Specific latent heat of fusion
Specific latent heat of vaporization

By the end of the lesson, the learner should be able to:
Define specific latent heat of fusion
- Determine latent heat of ice by method of mixtures
- Perform electrical method for latent heat
- Calculate latent heat from experimental data

In groups, learners are guided to:
Method of mixtures experiment using ice and warm water
- Electrical method using ice and immersion heater
- Heat balance calculations
- Determination of specific latent heat values

Ice, Calorimeter, Thermometer, Electrical heater, Filter funnels, Beakers, Measuring cylinders
Steam generator, Condenser, Calorimeter, Electrical heater, Measuring instruments, Safety equipment

KLB Secondary Physics Form 3, Pages 220-223

Quantity of Heat

Effects of pressure and impurities on melting and boiling points
Evaporation and cooling effects

By the end of the lesson, the learner should be able to:
Investigate effect of pressure on melting point of ice
- Demonstrate regelation phenomenon
- Investigate effect of pressure on boiling point
- Explain effect of impurities on phase transition temperatures

In groups, learners are guided to:
Regelation experiment with ice and wire
- Pressure effect on boiling point using flask
- Salt solution boiling point investigation
- Discussion on pressure cooker working

Ice blocks, Weighted wire, Round-bottomed flask, Thermometer, Salt solutions, Pressure cooker model
Various liquids, Beakers, Fans, Thermometers, Ether, Test tubes, Humidity measuring devices

KLB Secondary Physics Form 3, Pages 227-230

Gas Laws

Introduction to gas behavior and Boyle's Law
Boyle's Law experiments and calculations
Boyle's Law applications and kinetic theory explanation

By the end of the lesson, the learner should be able to:
Describe relationship between pressure and volume of gases
- State Boyle's Law
- Demonstrate pressure-volume relationship using syringe
- Plot P vs V and P vs 1/V graphs

In groups, learners are guided to:
Q/A on gas properties from previous studies
- Demonstration using syringe to show pressure-volume relationship
- Discussion on molecular explanation
- Introduction to gas law investigations

Syringes, J-shaped tubes, Oil, Bourdon gauge, Foot pump, Metre rule, Graph paper
Thick-walled J-shaped tube, Oil, Pressure gauge, Measuring instruments, Data tables, Graph paper, Calculators
Problem worksheets, Kinetic theory diagrams, Calculator, Gas bubble scenarios, Atmospheric pressure data

KLB Secondary Physics Form 3, Pages 235-237

Gas Laws

Charles's Law
Charles's Law applications and absolute temperature scale
Pressure Law (Gay-Lussac's Law)
Combined gas laws and ideal gas behavior

By the end of the lesson, the learner should be able to:
State Charles's Law for constant pressure processes
- Demonstrate volume-temperature relationship
- Perform experiments to verify V ∝ T relationship
- Plot V vs T and V vs θ graphs
State relationship between pressure and temperature at constant volume
- Demonstrate pressure-temperature experiments
- Verify P ∝ T relationship
- Derive pressure law formula

In groups, learners are guided to:
Experiment using gas column in tube with varying temperature
- Temperature and volume measurements
- Graph plotting showing linear relationship
- Discussion on absolute zero concept
Experiment using constant volume gas with temperature variation
- Pressure measurements at different temperatures
- Graph plotting of P vs T
- Verification of linear relationship through origin

Gas tubes, Water baths, Thermometers, Measuring cylinders, Heating apparatus, Graph paper, Temperature control equipment
Temperature conversion charts, Problem sets, Calculators, Hot air balloon examples, Gas heating scenarios
Constant volume gas apparatus, Pressure gauges, Temperature control, Water baths, Thermometers, Graph materials
Combined law worksheets, Complex problem sets, Calculators, Ideal gas assumption charts

KLB Secondary Physics Form 3, Pages 238-241
KLB Secondary Physics Form 3, Pages 242-244

Gas Laws

Kinetic theory of gases
Absolute zero and temperature scales

By the end of the lesson, the learner should be able to:
State basic assumptions of kinetic theory
- Explain gas laws using molecular motion
- Relate temperature to average kinetic energy
- Analyze molecular behavior in different conditions

In groups, learners are guided to:
Discussion of kinetic theory postulates
- Molecular explanation of gas laws
- Mathematical relationship between temperature and kinetic energy
- Analysis of molecular motion at different temperatures

Kinetic theory diagrams, Molecular motion animations, Temperature-energy relationship charts, Theoretical discussion materials
Graph paper, Extrapolation exercises, Temperature scale diagrams, Conversion worksheets, Scientific calculators

KLB Secondary Physics Form 3, Pages 244-245

Gas Laws

Comprehensive applications and problem solving

By the end of the lesson, the learner should be able to:
Solve complex multi-step gas law problems
- Apply gas laws to real-world situations
- Analyze atmospheric and weather-related phenomena
- Review all gas law concepts and applications

In groups, learners are guided to:
Comprehensive problem solving session
- Analysis of weather balloons, scuba diving, and atmospheric pressure effects
- Review of all gas laws
- Preparation for examinations with complex scenarios

Past examination papers, Multi-step problem sets, Real-world scenario worksheets, Summary charts, Calculators

KLB Secondary Physics Form 3, Pages 235-245